Voron 0.1 Wiring Harness made by LINNEO



A Linneo Wiring Harness is custom made and has a dispatch time of  up to 4 weeks! 

Are you not really a wiring guy, don’t like crimping? Here’s the solution: the Voron 0.1 wiring harness. Perfectly fitted for your Voron printer, made in Europe by LINNEO to highest quality standards. This gives you the advantage of short delivery times but at the same time a high customisation level to match your printer configuration.

The Voron 0.1 Heluflon harness is made from 0.25mm2 (0.5mm2 for heater wires) FEP cable. It is terminated with JST or Molex connectors and fully labelled. The necessary connector counter parts also included.

The harness is compatible with the SKR Mini E3 V2 & V3.

You can choose the colour of the sleeving (black, blue, green, orange or red). All harnesses will come in two colours of wiring: main wire colour black plus contrast wires in the same colour as the selected sleeve.

You can check the FAQ section which parts of the wiring are included and how to use the harness correctly.

If you need any more adjustments, let us know and we can get the loom even more customised for you.

The Linneo 0.1 wiring harnesses are not compatible with the Umbilical PCBs (please buy the Linneo Umbilical Harness instead).



Weight 0.35 kg
Dimensions 35 × 25 × 5 cm

Black, Blue, Green, Orange, Red, Yellow


There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

  • Which versions of the Afterburner Toolhead PCB (by HartK) are the Linneo harnesses compatible with?
    The harnesses are compatible with versions 3.1, 3.2, 4.0 and V3.rabbit of the Afterburner Toolhead PCB (up to 15/04/2022). After that date all "toolhead compatible" harnesses have been made for the HartK Stealthburner PCB . Please select the correct configuration of the harness, when you order it.
  • What do the abbreviations mean on the labels?
    Here the abbreviations used on the cable harness connectors: AM: A motor BM: B motor HO: Hotend heater 0 XY: X and Y endstops (only V2.4 variants) XE: X Endstop (only SW, V0.1 and V1.8 variants) E0: Extruder motor 0 T0: Thermistor 0 PF: Part cooling fan HF: Hotend fan BL (in earlier versions: PR): Bed leveling probe CT: chamber thermistor (in Afterburner Toolhead PCB variants) FS: filament sensor (for future use, not included yet) 24: 24V power supply (in Afterburner Toolhead PCB variants)
  • Which connector types are being used?
    The harnesses are built using JST XH connectors or MicroFit where needed. If the terminated end of a harness cannot plug directly into a component, the fitting counterpart connectors and pins are included.
  • Which wiring is included in the harness?
    The harnesses include all  the PTFE (Heluflon) low voltage wiring between the controller board and the steppers/toolhead/extruder which needs to be heat resistant and be fed through drag chains. High-voltage wiring (e.g. to the heated bed or from the mains power inlet to the power supplies) or general power wiring is included as wiring DIY pack, which provides you all necessary components to build the auxiliary harness (not included in the Linneo Lite harnesses). Also if the existing wires stepper motors come with wire which can be used (because it doesn't need to be PTFE) this is not included (e.g. the z stepper wiring for the Voron 2.4)
  • What is the delivery time?
    Every harness is made to order (except it is shown as "in stock" in this case the harness is ready for shipment immidiately) and has a delivery time as indicated on the article page.
  • Which printer variants are supported by Linneo harnesses?

    At the moment we are supporting:

    • Voron 0/0.1 (the Voron 0 can use the V0.1 harness, there will be a few wires spare, which can be used later on if you want to upgrade from 0 to 0.1)
    • Voron 2.4/Trident (250, 300 and 350 variants)
    • Voron Switchwire

    Special requirements (e.g. larger beds, taller z height, different electronics) can be supported on request, just contact us.

  • Is a BAT85 diode integrated in the harness?
    It depends. If you are going for an Afterburner PCB variant, the BAT85 diode is already on the PCB, so not necessary to be included in the harness. The same if you are going for a Spider board or a newer Duet, here the BAT85 is already included on the board. If you go for a SKR variant without the Afterburner PCB (V2.4 or Switchwire), the BAT85 will be place within the harness.
  • Shopping Cart
    Scroll to Top