Voron 2.4 (250mm) Bill of Material
All components available on OneTwo3D have been linked. Kits are shown on top of each section and kit components included are marked with a “x” in the table. Please check for changes to the latest BOM on vorondesign.com
| Part Description | Qty. | OneTwo3D Kit (option 1) | OneTwo3D Kit (option 2) |
|---|---|---|---|
| Fasteners | Voron 2.4 Fastener Kit (silver) | Voron 2.4 Fastener Kit (black) | |
| M5x40 SHCS | 22 | x | x |
| M5x30 BHCS | 22 | x | x |
| M5x16 BHCS | 35 | x | x |
| M5x10 BHCS | 35 | x | x |
| M5 Post-install T-nut | 68 | x | x |
| M5 Hexnut | 16 | x | x |
| M5 1mm Shim | 42 | x | x |
| M4x6 BHCS | 7 | x | x |
| M4 Knurled Nut (DIN 466-B) | 4 | x | x |
| M3x8 SHCS | 173 | x | x |
| M3x6 FHCS | 8 | x | x |
| M3x6 BHCS | 11 | x | x |
| M3x40 SHCS | 30 | x | x |
| M3x30 SHCS | 25 | x | x |
| M3x20 SHCS | 22 | x | x |
| M3x16 SHCS | 20 | x | x |
| M3x12 SHCS | 41 | x | x |
| M3x10 FHCS | 4 | x | x |
| M3 Washer | 3 | x | x |
| M3 Threaded Insert (M3x5x4) | 110 | x | x |
| M3 Post-install T-nut | 89 | x | x |
| M3 Hexnut | 6 | x | x |
| M3 Hammer Head T-nuts | 60 | x | x |
| M2x10 Self-tapping Screw | 16 | x | x |
| Rubber Foot (1.5x.75" 38x19mm) | 4 | ||
| Motion | Voron 2.4 250mm Motion Kit | Voron 2.4 250mm Linear Rail Kit (LDO) | |
| Ø5x60mm Shaft D Cut | 4 | x | |
| Ø5x35mm Shaft (trim to size) | 1 | x | |
| GT2 Open Belt LL-2GT-9 (9mm wide) - 1000mm | 4 | x | |
| GT2 Open Belt LL-2GT-6 (6mm wide) - 1600mm | 2 | x | |
| GT2 Belt Loop (6mm W) - 188mm | 4 | x | |
| GT2 80T Pulley (5mm ID 6mm W) | 4 | x | |
| GT2 20T Toothed Idler (5mm ID 9mm W) | 4 | x | |
| GT2 20T Toothed Idler (5mm ID 6mm W) | 2 | x | |
| GT2 20T Pulley (5mm ID 9mm W) | 4 | x | |
| GT2 20T Pulley (5mm ID 6mm W) | 3 | x | |
| GT2 16T Pulley (5mm ID 6mm W) | 4 | x | |
| F695 Bearing | 20 | x | |
| BMG Extruder Components Kit | 1 | x | |
| 625 Bearing | 12 | x | |
| Linear Rail MGN9H 300mm | 6 | Hiwin Rails | x |
| Linear Rail MGN12H 300mm | 1 | Hiwin Rails | x |
| Electronics | Voron 2.4 Stepper Motor Kit | OctopusPro with steppers | |
| USB Cable for selected controller | 1 | ||
| TycoElectronics 10EGG1-2 Filtered Power Inlet (EU) | 1 | ||
| TycoElectronics 10EGG1-1 Filtered Power Inlet (NA/UK) | 1 | ||
| Thermal Fuse (125C) | 1 | ||
| TMC2209 Stepper Motor Driver | 7 | x | |
| RaspberryPi 3B+ or better | 1 | ||
| Omron G3A-210B-DC5 SSR | 1 | ||
| Omron D2F-01L Micro Switch | 3 | ||
| NEMA17 Motor 17HS19-2004S | 6 | x | |
| NEMA17 Motor 17HS19-2004S | 1 | x | |
| NEMA14 Motor 36STH20-1004AHG | |||
| Mini 12864 Display | 1 | ||
| Medium Blow Fuse 5x20mm 8A (120v mains) | 1 | ||
| Medium Blow Fuse 5x20mm 4A (220V mains) | 2 | ||
| Mean Well RS-25-5 PSU | 1 | LDO Compact Power Supply (LCP300-24D5) | |
| Mean Well LRS-200-24 PSU | 1 | LDO Compact Power Supply (LCP300-24D5) | |
| Keystone CAT6 Insert (Optional) | 1 | ||
| Inductive Probe (See sourcing guide) | 1 | ||
| Hotend Kit (24V) | 1 | ||
| DIN Rail Mount Bracket for G3A SSR | 1 | ||
| Controller with 7+ Stepper outputs | 1 | x | |
| C13 Power Cord | 1 | ||
| BAT85 Diode | 1 | ||
| 60x60x20 Fan (24V) | 3 | ||
| 40x40x20 Centrifugal Fan (24V)/50x50x15 Centrifugal Fan (24V) | 1 | ||
| 40x40x10 Axial Fan (24V) | 1 | ||
| Frame | Misumi Frame Set | LDO Frame Set | |
| OpenBuilds Billet Angle Corner Connector (2020) | 4 | x | x |
| Misumi HFSB5-2020-430-LCP-RCP | 4 | x | x |
| Misumi HFSB5-2020-370-TPW | 10 | x | x |
| Misumi HFSB5-2020-350 | 2 | x | x |
| Misumi HFSB5-2020-330 | 1 | x | x |
| Misumi HFSB5-2020-240 | 1 | x | x |
| DIN 3 Rails (35mm W) - 365mm | 2 | ||
| Misc | |||
| Ø6x3mm Neodimium Magnet | 8 | ||
| Single Sided Foam Tape 3mm Thick (5m) | 1 | ||
| Single Sided Foam Tape 1mm Thick (5m) | 1 | ||
| PTFE Tube (4mm OD 3mm ID) - 1000mm | 1 | ||
| PTFE Tube (4mm OD 2mm ID) - 300mm | 1 | ||
| Mobil EP1/2 Grease | 1 | ||
| Loctite Blue Threadlocker Stick | 1 | ||
| Fume Extractor Carbon Filter Element | 1 | ||
| 4mm Threaded Bowden Coupler | 1 | ||
| 3M VHB Tape 5952 | 1 | ||
| Cables | |||
| WAGO 221-415 Lever-Nuts | 3 | ||
| Ring Crimp Terminal (16-22AWG #6) | 1 | ||
| Nylon Cable Ties Small (.07-.10" 1.8-2.7mm wide) | 42 | ||
| MicroFit3 Male Pin | 40 | Microfit Connector Kit | |
| MicroFit3 Female Pin | 40 | x | |
| MicroFit3 Connector Receptacle 4 Position | 4 | x | |
| MicroFit3 Connector Receptacle 3 Position | 1 | x | |
| MicroFit3 Connector Receptacle 2 Position | 2 | x | |
| MicroFit3 Connector Plug 4 Position | 4 | x | |
| MicroFit3 Connector Plug 3 Position | 1 | x | |
| MicroFit3 Connector Plug 2 Position | 2 | x | |
| MLX Power Receptacle 3 Position (bed wiring) | 1 | x | |
| MLX Power Plug 3 Position | 1 | x | |
| MLX Male Pin | 6 | x | |
| MLX Female Pin | 6 | x | |
| JST XH Connector 3 Position Male/Female Pair plus Pins | 1 | ||
| Fork Spade Crimp Terminal (18-22AWG #10) | 5 | ||
| Female Spade Crimp Terminal (18-22AWG .250" 6.35mm) | 7 | ||
| Crimp Ferrule Kit (covering sizes 24AWG to 18AWG) | 1 | ||
| Connector kit matching your controller choice (usually JST-XH) | 1 | ||
| 22-24AWG High-flex Wire (min 19 strand)(250ft/76m total) | 1 | ||
| 20AWG High-flex Wire (10ft/3m total) | 1 | ||
| 18AWG Wire (10ft/3m total) | 1 | ||
| IGUS E2i-10-10-018-0 Chain (305mm/1ft) | 2 | Igus Cable Chain Kit | |
| IGUS E2-150-10-12PZ Chain Ends (set) | 1 | x | |
| IGUS E2-15-10-028-0 Chain (445mm/1.46ft) | 1 | x | |
| IGUS E2-100-10-12PZ Chain Ends (set) | 2 | x | |
| Panels | Linneo Deck & Back Panel Kit | Linneo PC sides Kit | |
| Coroplast Sheet - 383x403x4 mm | 1 | x | |
| Coroplast Sheet - 369x369x4 mm | 2 | x | |
| Acrylic Sheet Clear - 383x403x3 mm | 2 | x | |
| Acrylic Sheet Clear - 383x383x3 mm | 1 | x | |
| Acrylic Sheet Clear - 191.5x403x3 mm | 2 | x | |
| Build Plate | |||
| Spring Steel Flexible Print Surface - 10"x10" | 1 | ||
| MIC6 5/16" Plate - 10"x10" | 1 | Mandala Roseworks Superflat/Magnetic | OneTwo3D MIC6 |
| Keenovo Silicone AC Heater w/ thermistor - 200x200mm (650W) | 1 | Our heaterpads are covering the full build plate, go for 250mm | |
| Adhesive Magnetic Sheet - 10"x10" | 1 | incl. with springsteel sheet |