Voron 0.2 Bill of Material
All components available on OneTwo3D have been linked. Kits are shown on top of each section and kit components included are marked with a “x” in the table. Please check for changes to the latest BOM on vorondesign.com
| Part Description | Qty. | OneTwo3D Kit (option 1) | OneTwo3D Kit (option 2) |
|---|---|---|---|
| Fasteners | LDO Voron 0.2 Fastener Kit | ||
| Makerbeam XL M3 t-nut | 2 | x | |
| M3x8 FHCS | 5 | x | |
| M3x8 BHCS | 115 | x | |
| M3x6 BHCS | 40 | x | |
| M3x40 BHCS | 10 | x | |
| M3x35 BHCS | 30 | x | |
| M3x30 BHCS | 10 | x | |
| M3x25 BHCS | 10 | x | |
| M3x16 BHCS | 10 | x | |
| M3x12 BHCS | 25 | x | |
| M3x10 BHCS | 30 | x | |
| M3 Nut | 140 | x | |
| M3 Brass heatstake inserts - short M3x5x4 | 50 | x | |
| M2x8 SHCS | 10 | x | |
| M2x6 FHCS | 10 | x | |
| M2x6 SHCS | 70 | x | |
| M2x10 Self Tapping Screws for Plastic | 30 | x | |
| M2 Nut | 55 | x | |
| 3x6x0.5 Shim Washers | 35 | x | |
| Frame | LDO Voron 0.2 Frame Kit | ||
| Makerbeam XL 15x15 200mm | 16 | x | |
| Makerbeam XL 15x15 100mm | 3 | x | |
| Top Hat Frame | |||
| Makerbeam XL 15x15 80-100mm | 4 | x | |
| Makerbeam XL 15x15 200mm | 4 | x | |
| Electronics | LDO Voron 0.2 Stepper Kit | ||
| V0 Display | 1 | ||
| RaspberryPi 3B+ or better | 1 | ||
| Omron Mouse Button - Micro Switch | 1 | ||
| NEMA17 Stepper Motor w/ integrated lead screw 200mm T8x8 | 1 | x | |
| NEMA14 Stepper Motor 40Ncm | 2 | x | |
| MicroSD Card | 1 | ||
| Meanwell LRS-150-24 | 1 | ||
| IEC320 C14 inlet | 1 | ||
| Hotend thermistor | 1 | ||
| Hotend | 1 | ||
| C13 Power Cord | 1 | ||
| Bigtreetech SKR Pico | 1 | ||
| 3M 5952 VHB tape | 1 | ||
| 3010 blower fans 24V | 2 | ||
| 3010 axial fan 24V | 1 | ||
| 24V Heater Cartridge | 1 | ||
| Cables | |||
| Wire 18gauge 10ft | 1 | ||
| Thermal Fuse 125C | 1 | ||
| Nylon Cable Ties (1.8mm wide or smaller) | 50 | ||
| Microfit3 Dual Row (10circuits) Male & Female Plug | 1 | ||
| JST connectors (2pin 3pin 4pin) | ? | ||
| Insulated Crimp Receptical | 4 | ||
| High Flex Wire 22gauge 100ft | 1 | ||
| High Flex Wire 20gauge 10ft | 1 | ||
| 7mm x 7mm cable chain (less than 1/2 meter needed) | 1 | ||
| Motion | LDO Voron 0.2 Motion Kit | LDO Linear Rail Kit | |
| T8x8 Anti-backlash Flange Nut | 1 | x (incl. in LDO Stepper motor Kit) | |
| MGN7H Linear Rail with Carriage - 150mm | 5 | Hiwin Rails | x |
| GT2 Open Belt (6mm W) - 3000mm | 1 | x | |
| GT2 20T (5mm ID 6mm W) | 2 | x | |
| F623-RS Bearing | 24 | x | |
| Buildplate | LDO Voron 0.2 Build Plate Kit | ||
| yellow die springs 8x4x20mm | 3 | ||
| Spring Steel Flex Buildplate 120x120mm (OPTIONAL) | 1 | Textured and Smooth PEI Coated Spring Steel Sheet | |
| Silicone DC 24V Heater 100x100mm 60W | 1 | x | |
| PEI + 3M 468MP (200MP) | 1 | x | 3M backed magsheet in LDO build plate kit, no PEI |
| MIC6 1/4" Plate - 120x120mm | 1 | Mandala Roseworks Super Flat Bed (magnetic/non-magnetic) | OneTwo3D Tooling Plate |
| Panels | |||
| Upper Rear Panel 212x63x3mm | 1 | Linneo Voron 0.2 ACM Deck & Back Panels | |
| Motor Panel 3mm thick (See DXF) | 1 | x | |
| Mid Panel 3mm thick (See DXF) | 1 | x | |
| Lower Rear Panel 212x185x3mm | 1 | x | |
| Deck Panel 3mm thick (See DXF) | 1 | x | |
| Bottom Panel 3mm thick (See DXF) | 1 | x | |
| Acrylic Sheet Clear - 212x239x2.5mm | 1 | Linneo Voron 0.1 & 0.2 PC Side Panels | |
| Acrylic Sheet Clear - 212x230x2.5mm | 2 | x | |
| Bowden | |||
| Bowden Tube 4x2mm - 1m | 1 | ||
| Bowden Fitting | 2 | ||
| Misc. | |||
| Medium Strength Thread Locker | 1 | ||
| Little Rubber Feet | 4 | ||
| Bowden Tube 4x3mm - 1m | 1 | ||
| 6x3mm Neodymium Magnet | 8 | ||
| Extrusion Top Hat Panels | Linneo Voron 0.2 Top Panel Kit | ||
| Top Panel 212x212mm | 1 | x | |
| Side Panels 212x(71-91)mm | 4 | x | |
| Extruder | |||
| NEMA14 36mm pancake Motor with 10 tooth gear | 1 | x (incl. in LDO Stepper motor Kit) | |
| MR85 Bearing | 2 | ||
| BMG Extruder Componets Kit | 1 |
